Plumbing Basics: A Must for Bathtub Installation
Plumbing Basics: A Must for Bathtub Installation
Blog Article
We have stumbled on this article about A Step-by-Step Guide to Installing a Bathtub below on the web and concluded it made sense to relate it with you on this page.
Mounting a tub isn't precisely brain surgery, yet it does need strong plumbing, woodworking, and sometimes, tiling abilities. Replacing an old bathtub with a new one is likewise a reasonably challenging task. If the old tub is easily easily accessible, the project can relocate immediately; if you need to open a wall surface to remove the old bathtub as well as position the new bathtub, the job is much harder. In either case, the task is within a house handyman's abilities, although you will certainly require an assistant to vacate the old tub as well as set in the new one. Make sure you have actually qualified on your own for the work as well as fit attempting it. Instead of employing a specialist to take control of a halfway-completed project, it is much better to consider employing one prior to you begin. Opportunities are you might require a professional plumber to make tube links.
This write-up will certainly assist you mount a brand-new bath tub in your restroom if you have actually already bought a brand-new tub as well as do not need to transform the setup of your previous water supply pipes.
Your tools and product checklist need to make up the following:
Preparing for the Installment
First of all, the supporting frame provided with the bathroom ought to be fitted (if needed) according to the manufacturer's instructions. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is very important to make sure that if the tap comes with a plastic washer, it is fitted between the bathroom and the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets unit to avoid pressure on the bathtub.
Fit the flexible tap connectors to the bottom of both taps utilizing 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet with the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Ensure you use all of the provided washers.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath ought to currently be ready to be suited its final position.
Removing Old Touches
If you require to replace old taps with new ones as a part of your installation, after that the first thing you must do is disconnect the water. After doing so, turn on the faucets to drain any type of water remaining in the system. The procedure of eliminating the existing faucets can be fairly problematic as a result of the limited gain access to that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the faucets. Have a fabric all set for the staying water that will come from the pipelines. As soon as the supply pipelines have actually been eliminated, utilize the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from transforming during this process. As soon as the faucets have been eliminated, the holes in the bath/basin will need to be cleansed of any old sealing compound.
Before proceeding to fit the new faucets, contrast the pipeline links on the old taps to the new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new faucets to fit.
Installing the Tub
Using both wooden boards under its feet, place the bath tub in the called for position. The wooden boards are helpful in uniformly spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto 4 little factors.
The next goal is to make certain that the bath tub is leveled all round. This can be accomplished by examining the level as well as changing the feet on the tub till the level checks out degree.
To mount taps, fit the bottom of the outermost flexible tap adapter to the appropriate supply pipe by making a compression join; then do the very same for the various other tap.
Activate the water and inspect all joints and new pipework for leaks and tighten them if required. Fill the tub as well as likewise examine the overflow outlet and the normal outlet for leakages.
Ultimately, deal with the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and securing around the bathtub should wait till the bath tub has actually been utilized at the very least once as this will certainly settle it into its final placement.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will need a plastic connector to stop damage to the thread. One end of the connector fits on the plastic tail of the faucet and the various other end supplies a connection to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly require decreasing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the tap in the installing hole in the bath/basin making sure that the washers are in location between the tap and also the sink. Protect the tap in position with the maker offered backnut. As soon as the tap is safely in place, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with regular tap connectors. The previous type needs to be connected to the faucet ends initially, tightening up just by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the location where the bath fulfills the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate enough to fracture an inflexible seal, triggering the water to permeate the wall in between the bathroom and also the tiling, bring about problems with moisture as well as possible leaks to the ceiling listed below.
You can pick from a range of coloured sealers to blend in your fixtures and also installations. They are marketed in tubes as well as cartridges, as well as are capable of securing voids as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of drenched newspaper or soft rope. Remember to always fill the tub with water before securing, to enable the movement experienced when the tub is in use. The sealer can fracture rather early if you do not consider this movement before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise easily available on the marketplace. It is a good idea to fit the tiles using water-resistant or water resistant glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you appreciate reading about How to Install a Bathtub? Try leaving a remark directly below. We'd be interested to see your feelings about this piece. In hopes that you come back again in the future. Are you aware of another person who is enthusiastic about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Please feel free to promote it. We truly appreciate reading our article about A Step-by-Step Guide to Installing a Bathtub.
Information Here Report this page